tvfaq Community

Запускал e2fsck с параметром -v и отвечал 'n' для получения отчёта без внесения правок.Выполнил e2fsck -p /dev/mmcblk0p7:

В итоге имидж перестал запускаться. После включения появляется логотип "Vu+" и далее "малевич". При этом реагирует на команды по Telnet. При попытке прошить оригинальный имидж, ведёт себя как и раньше.

Запустил e2fsck, на все вопросы отвечал no. Выкладываю скрины:Что можно сказать по этому поводу?

Цитата: Ednaz от 08 апреля 2024, 07:27:53
Вважаю, що потрібно шукати файл bolt_auto.bin для Zero4k. В мене нажаль немає і Marusys взагалі прибрав доступ до архіву VU Plus.

Розумію неразі знайти bolt_auto.bin нереально?

Цитата: sety от 07 апреля 2024, 13:44:26а этот старый имидж- он рабочий? Если да попробуйте его обновить или прошить онлайн в меню должны быть эти пункты

Старый имидж работает если ничего не пытаться сохранить изменения настроек, иначе вылет в "зелёный экран". Обновить пытался, скачивает 1 пакет, перезапускается с вылетом в "зелёный экран". После запуска никаких очевидных изменений не видно.

Пробовал установить SatDreamGR, индикатор плавно мигает 15-20сек и начинает мигать прерывисто. Выключаю, вынимаю флешку, включаю питание - запускается старый имидж 

Цитата: berimor18 от 05 апреля 2024, 17:16:06рецепт - сначала устанавливаеш имидж SatDreamGR а потом опенблекхол а далее какой хочеш.

Цитата: berimor18 от 05 апреля 2024, 17:18:36до выше сказаного - имидж только на питоне2 устанавливаеш

Попробую и этот способ, о результате отпишусь. Подскажите, где скачать SatDreamGR (PY2), а то смотрел, найти не могу...

Вибачаюсь, доступ вже є. Коли знімав цей лог використовував саме оригінальний образ vuplus-image-vuzero4k-20230613154111_usb.zip. Нажаль результату немає 

Ednaz, Дякую Вам за пораду, нажаль не можу отримати доступ до оригінального іміджа за вказаним посиланням. Хочу спробувати утиліту e2fsck, підскажіть чи може вона допомогти?

Здравствуйте друзья, снова вернулся к попытке перепрошить свой Zero4K. Сделал кабель-переходник RJ12 - COM-порт. Смог снять лог "неудачной" перепрошивки. Выкладываю фрагмент лога момента индикации светодиода.[spoiler]starting pid 1284, tty '': '/bin/cttyhack /bin/sh -l'
# [    3.323070] scsi 1:0:0:0: Direct-Access     General  USB Flash Disk   1100 PQ: 0 ANSI: 4
[    3.331695] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    3.338573] sd 1:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB)
[    3.348361] sd 1:0:0:0: [sda] Write Protect is off
[    3.361518] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.390160]  sda: sda1
[    3.397459] sd 1:0:0:0: [sda] Attached SCSI removable disk
[    3.468638] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    3.494274] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
[    3.515569] EXT4-fs warning (device mmcblk0p7): ext4_clear_journal_err:4736: Filesystem error recorded from previous mount: IO failure
[    3.527696] EXT4-fs warning (device mmcblk0p7): ext4_clear_journal_err:4737: Marking fs in need of filesystem check.
[    3.538721] EXT4-fs (mmcblk0p7): warning: mounting fs with errors, running e2fsck is recommended
[    3.547892] EXT4-fs (mmcblk0p7): recovery complete
[    3.552917] EXT4-fs (mmcblk0p7): mounted filesystem with journalled data mode. Opts: data=journal
[    3.575485] EXT4-fs error (device mmcblk0p7): ext4_mb_generate_buddy:757: group 1, block bitmap and bg descriptor inconsistent: 27440 vs 27442 free clusters
[    3.589558] Aborting journal on device mmcblk0p7-8.
[    3.595053] EXT4-fs (mmcblk0p7): Remounting filesystem read-only
[    3.601088] EXT4-fs error (device mmcblk0p7) in ext4_free_blocks:4873: Journal has aborted
[    3.609582] EXT4-fs error (device mmcblk0p7) in ext4_ext_remove_space:3042: IO failure
[    3.617734] EXT4-fs error (device mmcblk0p7) in ext4_ext_truncate:4654: Journal has aborted
[    3.626308] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
[    3.635496] EXT4-fs error (device mmcblk0p7) in ext4_truncate:3808: Journal has aborted
[    3.643722] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
[    3.652911] EXT4-fs error (device mmcblk0p7) in ext4_orphan_del:2987: Journal has aborted
[    3.661311] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
[    4.041959] bcmgenet f0480000.ethernet eth0: Link is Down
[    4.245444] EXT4-fs error (device mmcblk0p7): ext4_put_super:789: Couldn't clean up the journal
[   57.072197] random: nonblocking pool is initialized[/spoiler]Также прикрепил полный лог[spoiler]Terminal log file
Date: 02.04.2024 - 16:30:15
-----------------------------------------------
ю<0>CPU 01
BCM72600000
PRID07260400
v1.32
RR:00000003
BFW
seclib-1.11
BBL v3.1.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 10002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00056000 part_offset: 00000000 bootStatus: 302b2500
MEMSYS-ALT
SHMOO 03040016 BLD:memsys_7260a_3.4.0.0_take2-39-gc791dfd02 HW:hpg0_b2p1 shmoo_ver:3.4.0.22
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=000003d1(977)
temperature=00009a09(39433)
PV=0000033a(826)
MV=000003d1(977)
CPU: Current voltage=000003d0(976)
temperature=00009a09(39433)
PV=0000032b(811)
MV=000003d0(976)
AVS FW rev=30353078 [0.5.0.x]
OK
DDR0: !@ ffe07800 <= ffe06c70 MEMSYS-0 @ f1100000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 2025252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v4.2.3
INFO v00000003
COPY CODE... DONE
MICH: disable success
SSBL
SEC: jtag debug status: 000000af
PINMUX
CACHE FLUSH OK
CLR PSCI MEM @ 06400000 OK
INSTALL smm64@06400000 OK
MMU ON
CACHE FLUSH OK
_fbss  070660a0
_ebss  0706b438
_end   0706b458
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 070660a0 to 0706b438 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
PSCI: Init...
PSCI: config @ 0000000006402d00 cpus:2 cpu idx:0
cpu 0 state:5
cpu 1 state:0
PSCI: v0.2

    ,/   
  ,'/___, BOLT v1.32 v1.32 LOCAL BUILD
.'__  ,'  (2018-07-27 13:33:44 Vuplus team)
   /,'    Copyright (C) 2018 Broadcom
  /'     

Board: BCM972604USFF
SYS_CTRL: product=72604, family=7260a0, strap=0000019e,00000011
otp @ 0xf0404030 = 0x000000e0: en_cr(0x00000060) en_testport(0x00000080)
otp @ 0xf0404034 = 0x00804000: macrovision_disable(0x00800000) mtsif_enc_ctl_disable(0x00004000)
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 24 possible causes)
RTS0: 0x21101004, 256 clients, ok
BOX MODE: 4
CPU: 2x B53 [420f1000] 1503 MHz
SCB: 388 MHz
SYSIF: 1002 MHz
DDR0 @ 1200MHz
SPLASH: starting
SPLASH BMEM init @ 7dffffff
SPLASH: Old format file in flash. Use splash_create_flash_file to create newer format.
Loaded BMP: W=720 H=480
SPLASH: audio not present
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.978V, T=+40.407C, PV=0.826V, MV=0.977V, FW=30353078 [0.5.0.x]
AVS: CPU: V=0.967V, T=+40.407C, PV=0.811V, MV=0.976V
boot device name [flash1]
waiting for usb...
usb: resetting device on bus 0 hub 1 port 1


USB: New high speed device connected to bus 0 hub 1 port 1

usb: found Mass-Storage Device 090c:1000

USBMASS: Unit 0 connected

done
checking usb
Found high priority Mass Storage bus = 0, index  = 0
checking front key
readFrontKey 0 0
Check ignore.update file
Checking usbdisk0:/vuplus/zero4k/ignore.update......NO
Check force.update file
Checking usbdisk0:/vuplus/zero4k/force.update......YES
bolt update ...Checking usbdisk0:/vuplus/zero4k/bolt_auto.bin......NO
Checking usbdisk0:/vuplus/zero4k/rootfs.tar.bz2......YES
Checking usbdisk0:/vuplus/zero4k/splash_auto.bin......YES
Checking usbdisk0:/vuplus/zero4k/kernel_auto.bin......YES
Checking usbdisk0:/vuplus/zero4k/reboot.update......NO
Update
Reading usbdisk0:/vuplus/zero4k/bolt_auto.bin: Reading usbdisk0:/vuplus/zero4k/bolt_auto.bin:  >> Failed.: File not found
Reading usbdisk0:/vuplus/zero4k/splash_auto.bin: Reading usbdisk0:/vuplus/zero4k/splash_auto.bin:  >> .
Done. 1036854 bytes read
Programming...
done. 1036854 bytes written
Reading usbdisk0:/vuplus/zero4k/initrd_auto.bin: Reading usbdisk0:/vuplus/zero4k/initrd_auto.bin:  >> .......
Done. 11370198 bytes read
Programming...
done. 11370198 bytes written
Reading usbdisk0:/vuplus/zero4k/kernel_auto.bin: Reading usbdisk0:/vuplus/zero4k/kernel_auto.bin:  >> ...
Done. 4481528 bytes read
Programming...
done. 4481528 bytes written
Checking usbdisk0:/vuplus/zero4k/rootfs.tar.bz2......YES
Flashing ..Loader:zimg Filesys:raw Dev:flash0.initrd File:(null) Options:(null)
Reading up to 33554432 bytes from Image.....
Starting program at 0x80000 (DTB @ 0x7618000)

64 bit PSCI boot...
PSCI: DTB @ 0000000007618000, Linux entry @ 0000000000080000
PWR_UP-CPU1 OK
BOOT64
ADDR-CPU1  0000000006402628 @ RDB: 20452008
ON-CPU1  00000002 @ 2020248c
GO-CPU1 @ 0000000000080f20
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.1.20-1.9 (gdhan@Notebook) (gcc version 4.8.5 (Broadcom stbgcc-4.8-1.5) ) #8 SMP Thu May 11 20:43:31 KST 2017
[    0.000000] CPU: AArch64 Processor [420f1000] revision 0
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] alternatives: enabling workaround for ARM erratum 845719
[    0.000000] moving dtb from 0x0000000007618000 to 0x0000000000000000
[    0.000000] brcmstb_memory_get_default_reserve: Split region 0x0000000070000000@0x0000000010000000, reserve will fail
[    0.000000] cma: Reserved 16 MiB at 0x000000007cc00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] PERCPU: Embedded 16 pages/cpu @ffffffc07deed000 s27904 r8192 d29440 u65536
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 509040
[    0.000000] Kernel command line:
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] software IO TLB [mem 0x76e00000-0x7ae00000] (64MB) mapped at [ffffffc076e00000-ffffffc07adfffff]
[    0.000000] Memory: 1932508K/2064384K available (6308K kernel code, 455K rwdata, 2560K rodata, 6888K init, 279K bss, 115492K reserved, 16384K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdffff0000   (   247 GB)
[    0.000000]     vmemmap : 0xffffffbe00000000 - 0xffffffbfc0000000   (     7 GB maximum)
[    0.000000]               0xffffffbe00000000 - 0xffffffbe01b90000   (    27 MB actual)
[    0.000000]     fixed   : 0xffffffbffabfd000 - 0xffffffbffac00000   (    12 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc07e000000   (  2016 MB)
[    0.000000]       .init : 0xffffffc00092a000 - 0xffffffc000fe4000   (  6888 KB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc000929934   (  8871 KB)
[    0.000000]       .data : 0xffffffc000fed000 - 0xffffffc00105ecd0   (   456 KB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]     Additional per-CPU info printed with stalls.
[    0.000000]     RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000002000, parent irq: 89)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000008000, parent irq: 61)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff800000aa00, parent irq: 62)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff800000c640, parent irq: 91)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff800000e200, parent irq: 57)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000010500, parent irq: 95)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000012400, parent irq: 96)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000014540, parent irq: 93)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000016440, parent irq: 94)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xffffff8000018480, parent irq: 98)
[    0.000000] Architected cp15 timer(s) running at 27.00MHz (phys).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[    0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[    0.000370] Console: colour dummy device 80x25
[    0.000827] console [tty0] enabled
[    0.000846] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[    0.000866] pid_max: default: 32768 minimum: 301
[    0.001002] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.001015] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.001611] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[    0.014876] CPU1: Booted secondary processor
[    0.014882] Detected VIPT I-cache on CPU1
[    0.014956] Brought up 2 CPUs
[    0.014987] SMP: Total of 2 processors activated.
[    0.014997] CPU: All CPU(s) started at EL2
[    0.015016] alternatives: patching kernel code
[    0.015319] devtmpfs: initialized
[    0.022331] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.022960] atomic64_test: passed
[    0.023685] NET: Registered protocol family 16
[    0.029223] cpuidle: using governor ladder
[    0.035225] cpuidle: using governor menu
[    0.035249] vdso: 2 pages (1 code @ ffffffc000ff5000, 1 data @ ffffffc000ff4000)
[    0.035291] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.035750] DMA: preallocated 256 KiB pool for atomic allocations
[    0.036083] Broadcom Brahma-B53 read-ahead cache at: 0xffffff80000e4478
[    0.051305] brcmstb-gpio f040a400.gpio: Registered 3 banks (GPIO(s): 0-95)
[    0.051481] brcmstb-gpio f04174c0.gpio: Registered 2 banks (GPIO(s): 96-159)
[    0.051914] SCSI subsystem initialized
[    0.052893] usbcore: registered new interface driver usbfs
[    0.052937] usbcore: registered new interface driver hub
[    0.052973] usbcore: registered new device driver usb
[    0.053034] Linux video capture interface: v2.00
[    0.053087] pps_core: LinuxPPS API ver. 1 registered
[    0.053097] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.053126] PTP clock support registered
[    0.053263] Advanced Linux Sound Architecture Driver Initialized.
[    0.053879] Switched to clocksource arch_sys_counter
[    0.058222] thermal thermal_zone0: failed to read out thermal zone (-22)
[    0.058341] NET: Registered protocol family 2
[    0.058636] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.058756] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.058990] TCP: Hash tables configured (established 16384 bind 16384)
[    0.059060] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.059102] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.059255] NET: Registered protocol family 1
[    0.059463] RPC: Registered named UNIX socket transport module.
[    0.059475] RPC: Registered udp transport module.
[    0.059484] RPC: Registered tcp transport module.
[    0.059493] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.247658] hw perfevents: Failed to parse /pmu/interrupt-affinity[0]
[    0.248389] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.249277] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.249451] NFS: Registering the id_resolver key type
[    0.249480] Key type id_resolver registered
[    0.249489] Key type id_legacy registered
[    0.249507] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.249539] jffs2: version 2.2. (NAND) В© 2001-2006 Red Hat, Inc.
[    0.249602] fuse init (API version 7.23)
[    0.255379] io scheduler noop registered
[    0.255442] io scheduler cfq registered (default)
[    0.255723] brcm-gisb-arb f0400000.gisb-arb: registered mem: ffffff800016a000, irqs: 2, 4
[    0.256334] brcmstb-sata-phy f0b10100.sata_phy: registered 1 port(s)
[    0.256685] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
[    0.256748] brcm-pci f0460000.pcie: no identity map; PCI drivers may fail
[    0.356892] brcm-pci f0460000.pcie: down
[    0.358261] brcmstb_memc f1102000.memc-ddr: registered
[    0.358449] brcm-waketimer f0417680.waketimer: registered, with irq 5
[    0.387216] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.388680] f040c000.serial: ttyS0 at MMIO 0xf040c000 (irq = 100, base_baud = 5062500) is a 16550A
[    1.110130] console [ttyS0] enabled
[    1.114238] f040d000.serial: ttyS1 at MMIO 0xf040d000 (irq = 101, base_baud = 5062500) is a 16550A
[    1.123698] f040e000.serial: ttyS2 at MMIO 0xf040e000 (irq = 102, base_baud = 5062500) is a 16550A
[    1.133341] [drm] Initialized drm 1.1.0 20060810
[    1.141994] brd: module loaded
[    1.147215] loop: module loaded
[    1.151189] brcm-ahci f0b12000.sata: controller can do ALPM, turning on CAP_ALPM
[    1.158624] brcm-ahci f0b12000.sata: masking port_map 0x1 -> 0x1
[    1.164665] brcm-ahci f0b12000.sata: SSS flag set, parallel bus scan disabled
[    1.181865] brcm-ahci f0b12000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    1.190854] brcm-ahci f0b12000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part
[    1.199258] scsi host0: brcm-ahci
[    1.202729] ata1: SATA max UDMA/133 mmio [mem 0xf0b12000-0xf0b1299b] port 0x100 irq 87
[    1.210676] brcm-ahci f0b12000.sata: Broadcom AHCI SATA3 registered
[    1.218224] libphy: Fixed MDIO Bus: probed
[    1.222908] bcmgenet f0480000.ethernet: GENET 5.0 EPHY: 0x0000
[    1.228794] bcmgenet f0480000.ethernet: failed to get enet-mux clock
[    1.247851] libphy: bcmgenet MII bus: probed
[    1.273400] Broadcom BCM7260 f0480000.etherne:01: failed to request GPHY clock
[    1.281469] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.287328] e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
[    1.293304] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    1.300774] usbcore: registered new interface driver pegasus
[    1.306483] usbcore: registered new interface driver asix
[    1.311921] usbcore: registered new interface driver ax88179_178a
[    1.315864] ata1: SATA down (SStatus 0 SControl 300)
[    1.323465] usbcore: registered new interface driver cdc_ether
[    1.329355] usbcore: registered new interface driver cdc_ncm
[    1.335185] xhci-brcm: xHCI BRCM driver
[    1.339196] ehci-brcm: EHCI BRCM driver
[    1.358014] ehci-brcm f0b00300.ehci_v2: EHCI Host Controller
[    1.363801] ehci-brcm f0b00300.ehci_v2: new USB bus registered, assigned bus number 1
[    1.381807] ehci-brcm f0b00300.ehci_v2: irq 120, io mem 0xf0b00300
[    1.393857] ehci-brcm f0b00300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.400426] hub 1-0:1.0: USB hub found
[    1.404207] hub 1-0:1.0: 1 port detected
[    1.408412] ehci-brcm f0b00500.ehci_v2: EHCI Host Controller
[    1.414176] ehci-brcm f0b00500.ehci_v2: new USB bus registered, assigned bus number 2
[    1.432137] ehci-brcm f0b00500.ehci_v2: irq 123, io mem 0xf0b00500
[    1.443857] ehci-brcm f0b00500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.450371] hub 2-0:1.0: USB hub found
[    1.454147] hub 2-0:1.0: 1 port detected
[    1.458380] ohci-brcm: OHCI BRCM driver
[    1.462372] ohci-brcm f0b00400.ohci_v2: BRCM OHCI controller
[    1.468149] ohci-brcm f0b00400.ohci_v2: new USB bus registered, assigned bus number 3
[    1.476087] ohci-brcm f0b00400.ohci_v2: irq 121, io mem 0xf0b00400
[    1.537186] hub 3-0:1.0: USB hub found
[    1.540968] hub 3-0:1.0: 1 port detected
[    1.545122] ohci-brcm f0b00600.ohci_v2: BRCM OHCI controller
[    1.550902] ohci-brcm f0b00600.ohci_v2: new USB bus registered, assigned bus number 4
[    1.559407] ohci-brcm f0b00600.ohci_v2: irq 124, io mem 0xf0b00600
[    1.620179] hub 4-0:1.0: USB hub found
[    1.623958] hub 4-0:1.0: 1 port detected
[    1.628182] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.634748] ehci-pci: EHCI PCI platform driver
[    1.639265] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.645475] ohci-pci: OHCI PCI platform driver
[    1.650067] usbcore: registered new interface driver usb-storage
[    1.656308] i2c /dev entries driver
[    1.660044] gspca_main: v2.14.0 registered
[    1.664432] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[    1.709412] brcmstb-avs-cpufreq f04c4000.avs-cpu-data-mem: registered
[    1.716104] sdhci: Secure Digital Host Controller Interface driver
[    1.722302] sdhci: Copyright(c) Pierre Ossman
[    1.726677] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.733843] sdhci-brcmstb f0200200.sdhci: No vmmc regulator found
[    1.739965] sdhci-brcmstb f0200200.sdhci: No vqmmc regulator found
[    1.776858] mmc0: SDHCI controller on f0200200.sdhci [f0200200.sdhci] using ADMA
[    1.784521] usbcore: registered new interface driver usbhid
[    1.792119] usbhid: USB HID core driver
[    1.796044] usb 1-1: new high-speed USB device number 2 using ehci-brcm
[    1.796464] NET: Registered protocol family 17
[    1.796496] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.796675] Key type dns_resolver registered
[    1.805256] ALSA device list:
[    1.805258]   No soundcards found.
[    1.835011] Freeing unused kernel memory: 6888K (ffffffc00092a000 - ffffffc000fe4000)
[    1.842881] Freeing alternatives memory: 24K (ffffffc000fe4000 - ffffffc000fea000)

starting pid 1176, tty '': '/etc/init.d/rcS'
Mounting virtual filesystems
[    1.888650] mmc0: MAN_BKOPS_EN bit is not set
Switching to conservative governor
* WARNING: THIS STB CONTAINS GPLv3 SOFTWARE
* GPLv3 programs mu[    1.903576] mmc0: new high speed MMC card at address 0001
st be removed in order to enable security.
* See: http://www.gn[    1.913956] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB
u.org/licenses/gpl-faq.html#Tivo[    1.920958] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB
ization
Configuring eth0 interf[    1.929428] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB
ace
[    1.938130] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB
[    1.946800]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
[    1.958600] usb-storage 1-1:1.0: USB Mass Storage device detected
[    1.996948] f0480000.etherne:01: Broadcom BCM7260 PHY revision: 0x01
[    2.007966] scsi host1: usb-storage 1-1:1.0
[    2.037074] bcmgenet f0480000.ethernet: configuring instance for internal PHY
Configuring lo interface
Starting network services

starting pid 1284, tty '': '/bin/cttyhack /bin/sh -l'
# [    3.323070] scsi 1:0:0:0: Direct-Access     General  USB Flash Disk   1100 PQ: 0 ANSI: 4
[    3.331695] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    3.338573] sd 1:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB)
[    3.348361] sd 1:0:0:0: [sda] Write Protect is off
[    3.361518] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.390160]  sda: sda1
[    3.397459] sd 1:0:0:0: [sda] Attached SCSI removable disk
[    3.468638] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    3.494274] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
[    3.515569] EXT4-fs warning (device mmcblk0p7): ext4_clear_journal_err:4736: Filesystem error recorded from previous mount: IO failure
[    3.527696] EXT4-fs warning (device mmcblk0p7): ext4_clear_journal_err:4737: Marking fs in need of filesystem check.
[    3.538721] EXT4-fs (mmcblk0p7): warning: mounting fs with errors, running e2fsck is recommended
[    3.547892] EXT4-fs (mmcblk0p7): recovery complete
[    3.552917] EXT4-fs (mmcblk0p7): mounted filesystem with journalled data mode. Opts: data=journal
[    3.575485] EXT4-fs error (device mmcblk0p7): ext4_mb_generate_buddy:757: group 1, block bitmap and bg descriptor inconsistent: 27440 vs 27442 free clusters
[    3.589558] Aborting journal on device mmcblk0p7-8.
[    3.595053] EXT4-fs (mmcblk0p7): Remounting filesystem read-only
[    3.601088] EXT4-fs error (device mmcblk0p7) in ext4_free_blocks:4873: Journal has aborted
[    3.609582] EXT4-fs error (device mmcblk0p7) in ext4_ext_remove_space:3042: IO failure
[    3.617734] EXT4-fs error (device mmcblk0p7) in ext4_ext_truncate:4654: Journal has aborted
[    3.626308] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
[    3.635496] EXT4-fs error (device mmcblk0p7) in ext4_truncate:3808: Journal has aborted
[    3.643722] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
[    3.652911] EXT4-fs error (device mmcblk0p7) in ext4_orphan_del:2987: Journal has aborted
[    3.661311] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
[    4.041959] bcmgenet f0480000.ethernet eth0: Link is Down
[    4.245444] EXT4-fs error (device mmcblk0p7): ext4_put_super:789: Couldn't clean up the journal
[   57.072197] random: nonblocking pool is initialized

-----------------------------------------------
Date: 02.04.2024 - 16:33:27
End log file
[/spoiler]
Прошу помочь с анализом этих данных

Друзья, так и не смог обновить имидж, ресивер работает, но заметил, что всё связанное с сохранением в памяти ресивера вызывает "зелёный экран". Не могу изменить настройки, не могу отсканировать спутники... Есть у кого ещё идеи, что делать?

Цитата: gievih link =topic=103.msg53340#msg53340 date=1703953303привыт ,а Ви не забували флешки перед загрузкою іміджа формуфати на компі в fat32?

Форматував і вбудованими засобами Windows і утилітою HP USB Disk Storage Format Tool в FAT32

Цитата: Ednaz от 26 декабря 2023, 22:30:17Використайте іншу флешку. 3 флешки це не показник. Можливо встановити імідж і через сервісний порт, але потрібен відповідний кабель RJ12-UART-USB

Спробував всі флешки які мав. Доречі, використовув також флешку з якої успішно прошивав цей ресивер попередні рази, але результат негативний.Мабуть доведеться спробувати через Vu+Util. Кабель можна десь придбати, чи потрібно виготовляти самому? Доречі, які логічні рівні на порту ресивера, TTL чи RS232?

Пытался перепрошить с отключёнными внешними устройствами, но результат тот же    Так же хотел сбросить ресивер к дефолтным установкам, но при попытке свалился в "зелёный экран", а после перезапуска все установки остались прежние.

Цитата: gievih от 22 декабря 2023, 15:00:54
привет Вы передетим чтото устанавливали?
если запускается на старом имидже ,то попробуйте поудалять все что устанавливали ранее ,(по фтр,или самим имиджем,)

Установлен только Wicard 1.19 и E-Panel 5.8-r2. Устанавливал сразу после прошивки имиджа, а последнее время не ставил ничего.

Цитата: gievih от 22 декабря 2023, 15:00:54
при прошивке еще попробуйте поодключать от реса все ,

Подключен TV по HDMI, кабель LNB и флешка (вместо USB "свистка"). Попробую всё отключить.

Подскажите, есть способы перепрошивки кроме как флешкой?