Сборки имиджей для Octagon SF4008 (обсуждения)

Автор Ednaz, 26 Вересень 2017, 11:41:14

Попередня тема - Наступна тема

0 Користувачі і 1 Гість дивляться цю тему.

Ednaz

Здесь ведем обсуждение сборок для Octagon SF4008 (сборки скачиваем здесь  link)
GI ET11000 4K, Duo4k, Ultimo4k, Solo4k, Uno4k, Uno4k SE, Zero4k, Octagon SF4008, AX HD51, Dreambox 900, Solo2, SoloSE v2, Zero, VU+Duo, Xtrend ET-9000, ET-9200, ET7000mini, Force1, Spark2, GI Fly и др.
Поблагодарить Z707779886070, E342760518570, R341155895525,  MasterCard 5168 7422 4047 5503monobank 5375 4141 1455 0253

romansat


Ednaz

Ок, буду смотреть. Сменю дрова для начала.
Там поправили уже эту проблему? Лог такой же как и был на этой сборке?
GI ET11000 4K, Duo4k, Ultimo4k, Solo4k, Uno4k, Uno4k SE, Zero4k, Octagon SF4008, AX HD51, Dreambox 900, Solo2, SoloSE v2, Zero, VU+Duo, Xtrend ET-9000, ET-9200, ET7000mini, Force1, Spark2, GI Fly и др.
Поблагодарить Z707779886070, E342760518570, R341155895525,  MasterCard 5168 7422 4047 5503monobank 5375 4141 1455 0253

romansat

Дрова в имидже нужны от 07.01.18.
Тоесть такие,какие есть в последнем oATV 6.2.
Иначе ни один имидж не станет поверх из OpenMultiboot.
Лог практически тот же.
Кстати вот пробую,загрузить установленный актуальный oATV 6.2 из флеши,вытянув флешку с мультибутом.
Не грузится,постоянный Starting linux tv...
Это подтверждение что OpenMultiboot переписывает оригинальный имидж во флеши.
Обычный бэкап тут не проходит.
Хорошо что я умею восстанавливать,сейчас восстановлю.

romansat

Посмотрел - в твоем имидже старые дрова.
Во флеш твой имидж установился.
Но тут же проблема,новый oATV 6.2 в тот же Мультибут поверх твоей сборки не  становится.
Так что итог такой - дрова должны совпадать,а также пакеты с фида,которые изменены под новые дрова
также должны быть идентичными.

romansat

Забыл написать.
Там кроме новых дров пофиксенный новый update.bin компатибильный с новыми дровами.
Одно без другого становиться не будет.

Ednaz

Пересобрал и перезалил имидж. Пробуй.
GI ET11000 4K, Duo4k, Ultimo4k, Solo4k, Uno4k, Uno4k SE, Zero4k, Octagon SF4008, AX HD51, Dreambox 900, Solo2, SoloSE v2, Zero, VU+Duo, Xtrend ET-9000, ET-9200, ET7000mini, Force1, Spark2, GI Fly и др.
Поблагодарить Z707779886070, E342760518570, R341155895525,  MasterCard 5168 7422 4047 5503monobank 5375 4141 1455 0253

romansat


Ednaz

Ох ты Ё, я не видел еще УПСов, с которых можно писать  :o
GI ET11000 4K, Duo4k, Ultimo4k, Solo4k, Uno4k, Uno4k SE, Zero4k, Octagon SF4008, AX HD51, Dreambox 900, Solo2, SoloSE v2, Zero, VU+Duo, Xtrend ET-9000, ET-9200, ET7000mini, Force1, Spark2, GI Fly и др.
Поблагодарить Z707779886070, E342760518570, R341155895525,  MasterCard 5168 7422 4047 5503monobank 5375 4141 1455 0253

Sage

Есть такой, я вот то же сейчас пишу с него, завалило снегом...  ;)
Полноценное электропитание на 2 суток.

Ednaz

GI ET11000 4K, Duo4k, Ultimo4k, Solo4k, Uno4k, Uno4k SE, Zero4k, Octagon SF4008, AX HD51, Dreambox 900, Solo2, SoloSE v2, Zero, VU+Duo, Xtrend ET-9000, ET-9200, ET7000mini, Force1, Spark2, GI Fly и др.
Поблагодарить Z707779886070, E342760518570, R341155895525,  MasterCard 5168 7422 4047 5503monobank 5375 4141 1455 0253

Sage


romansat

Ну у меня не такой крутой УПС,но вчера тоже завалило снегом ,свет исчез,и писал конечно с компа,запитанном от УПСа + роутер тоже к нему подключен..
Рес соответственно был без питания.

Сейчас буду ставить,отпишусь.

romansat

На этот раз поставил не в Мультибут а во флеш.
Booting ... forever )))

Ниже полный лог установки и последующей загрузки имиджа.
Там внизу написано чего ему не хватает.

Spoiler
CPU 01
BCM74390011
PRID07251111
v1.19
RR:00000003
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138 HW:hpf0_b1p6 V:2.1.0.0
MCB: FIX
AVS start:status=000000ff
STB: Current voltage=00000392(914)
temperature=00005d29(23849)
PV=00000351(849)
MV=00000392(914)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: *@ ffe0c7c8 <= ffe0c7c8 MEMSYS-0 @ f1100000 OK
DDR1: -
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  0704e420
_ebss  0704fc88
_end   0704fca8
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0704e420 to 0704fc88 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

    ,/
  ,'/___, BOLT v1.19 v1.19 LOCAL BUILD
.'__  ,'  (2016-10-14 22:06:19 doolgun@ubuntu)
   /,'    Copyright (C) 2016 Broadcom
  /'

Board: SF4008_EMMC_DDR4
SYS_CTRL: product=72511, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822080e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) memsys_1_disable(0x00008000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000461: moca2_disable(0x00000001) pcie1_disable(0x00000040) rfm_disable(0x00000020) sata1_disable(0x00000400)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1200MHz, DDR1 N/A
RESET CAUSE: 0x000003 main_chip_input power_on (2 of 23 possible causes)
CS0: SFDP SPI, 8MB, 64kB blocks, 64kB erase block, 256B pages
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 1
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.913V, T=+24.823C, PV=0.849V, MV=0.914V, FW=30333278 [0.3.2.x]
USB otp=00000040
Board version 0.92
HCS16SM18T Init
HCS16SM18T Reset
usb: resetting device on bus 0 hub 1 port 1
USB: New high speed device connected to bus 0 hub 1 port 1
usb: found Mass-Storage Device 090c:6200
USBMASS: Unit 0 connected
usb: resetting device on bus 1 hub 1 port 1
USB: New high speed device connected to bus 1 hub 1 port 1
usb: resetting device on bus 1 hub 2 port 1
USB: New high speed device connected to bus 1 hub 2 port 1
usb: found Mass-Storage Device 8564:1000
USBMASS: Unit 1 connected
Power Btn Init
LED Init
HDD Power Init
[ssbl/main/linux_dvb_7439.c::linux_dvb_usb_upgrade(653)] LINUX_DVB_DIR_PATH: sf4008
checking usbmass for upgrade
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/update.bin: File found
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/force: File not found
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/noforce: File found
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/rootfs.tar.bz2: File found
force:0 - noforce:1
[linux_dvb_upgrade:551] disk_number: 1
power button pressed
Reading usbdisk1:sf4008/bolt.bin: Failed.: File not found
Reading usbdisk1:sf4008/splash.bin: Failed.: File not found
Reading usbdisk1:sf4008/update.bin: .
Done. 8154144 bytes read
Programming...done. 8154144 bytes written
Reading usbdisk1:sf4008/kernel.bin: .
Done. 3388016 bytes read
Programming...done. 3388016 bytes written
Loader:zimg Filesys:raw Dev:emmcflash0.update File:(null) Options:(null)
Reading 8154144 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7628000)

32 bit boot...
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.1.20-1.5 (doolgun@ubuntu) (gcc version 4.8.5 (Broadcom stbgcc-4.8-1.5) ) #9 SMP Fri Sep 8 19:56:12 KST 2017
[    0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine model: SF4008_EMMC_DDR4
[    0.000000] moving dtb from 0x0000000007628000 to 0x0000000000d8aa20
[    0.000000] bmem: Reserved 768 MiB at 0x0000000010000000
[    0.000000] cma: Reserved 16 MiB at 0x000000000ec00000
[    0.000000] Forcing write-allocate cache policy for SMP
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 12 pages/cpu @cfdae000 s16832 r8192 d24128 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 261632
[    0.000000] Kernel command line:
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 223144K/1048576K available (6193K kernel code, 273K rwdata, 1992K rodata, 5140K init, 222K bss, 809048K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0806970   (8187 kB)
[    0.000000]       .init : 0xc0807000 - 0xc0d0c000   (5140 kB)
[    0.000000]       .data : 0xc0d0c000 - 0xc0d504c0   ( 274 kB)
[    0.000000]        .bss : 0xc0d53000 - 0xc0d8aa20   ( 223 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0802000, parent irq: 93)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0808000, parent irq: 64)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd080a640, parent irq: 95)
[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd080c200, parent irq: 58)
[    0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc40a700, parent IRQ(s): 2)
[    0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xd080e380, parent IRQ(s): 3)
[    0.000000] MCP: Enabling write pairing
[    0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[    0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[    0.000011] Switching to timer-based delay loop, resolution 37ns
[    0.000370] Console: colour dummy device 80x30
[    0.000391] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[    0.000401] pid_max: default: 32768 minimum: 301
[    0.000501] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000507] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001022] CPU: Testing write buffer coherency: ok
[    0.001202] CPU0: update cpu_capacity 1024
[    0.001209] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.001285] Setting up static identity map for 0x8440 - 0x8498
[    0.004052] CPU1: update cpu_capacity 1024
[    0.004056] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.004116] Brought up 2 CPUs
[    0.004128] SMP: Total of 2 processors activated (108.00 BogoMIPS).
[    0.004132] CPU: All CPU(s) started in SVC mode.
[    0.004427] devtmpfs: initialized
[    0.013452] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[    0.013671] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.014966] NET: Registered protocol family 16
[    0.015540] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.021152] cpuidle: using governor ladder
[    0.027163] cpuidle: using governor menu
[    0.033139] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.033150] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.033273] Broadcom Brahma-B15 readahead cache at: 0xd0910478
[    0.047650] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
[    0.047865] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
[    0.048436] SCSI subsystem initialized
[    0.049601] usbcore: registered new interface driver usbfs
[    0.049636] usbcore: registered new interface driver hub
[    0.049670] usbcore: registered new device driver usb
[    0.049745] Linux video capture interface: v2.00
[    0.049770] pps_core: LinuxPPS API ver. 1 registered
[    0.049774] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.049789] PTP clock support registered
[    0.050100] Advanced Linux Sound Architecture Driver Initialized.
[    0.051207] Switched to clocksource arch_sys_counter
[    0.058443] thermal thermal_zone0: failed to read out thermal zone (-22)
[    0.058547] NET: Registered protocol family 2
[    0.058845] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.058862] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.058884] TCP: Hash tables configured (established 2048 bind 2048)
[    0.058917] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.058928] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.059046] NET: Registered protocol family 1
[    0.059388] RPC: Registered named UNIX socket transport module.
[    0.059394] RPC: Registered udp transport module.
[    0.059397] RPC: Registered tcp transport module.
[    0.059401] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.179176] CPU PMU: Failed to parse /pmu/interrupt-affinity[0]
[    0.179249] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.180040] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.181116] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.181346] NFS: Registering the id_resolver key type
[    0.181369] Key type id_resolver registered
[    0.181373] Key type id_legacy registered
[    0.181388] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.181419] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.181492] fuse init (API version 7.23)
[    0.182193] bounce: pool size: 64 pages
[    0.182251] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.182260] io scheduler noop registered
[    0.182267] io scheduler deadline registered
[    0.182277] io scheduler cfq registered (default)
[    0.182503] brcm-gisb-arb f0400000.gisb-arb: registered mem: d0994000, irqs: 261, 262
[    0.182913] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
[    0.248489] brcmstb-sata-phy f0458100.sata_phy: registered 2 port(s)
[    0.248846] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
[    0.248897] brcm-pci f0460000.pcie: cannot get msi intr; MSI disabled
[    0.349023] brcm-pci f0460000.pcie: link down
[    0.350016] brcmstb_memc f1102000.memc-ddr: registered
[    0.350051] brcmstb_memc f1182000.memc-ddr: registered
[    0.350402] brcm-waketimer f0417580.waketimer: rtc core: registered brcmstb-waketmr as rtc0
[    0.350414] brcm-waketimer f0417580.waketimer: registered, with irq 263
[    0.388483] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.390100] console [ttyS0] disabled
[    0.390134] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[    1.110277] console [ttyS0] enabled
[    1.114393] f040a940.serial: ttyS1 at MMIO 0xf040a940 (irq = 108, base_baud = 5062500) is a 16550A
[    1.123839] f040a980.serial: ttyS2 at MMIO 0xf040a980 (irq = 109, base_baud = 5062500) is a 16550A
[    1.138279] brd: module loaded
[    1.144141] loop: module loaded
[    1.148307] brcm-ahci f045a000.sata: masking port_map 0x3 -> 0x3
[    1.154363] brcm-ahci f045a000.sata: SSS flag set, parallel bus scan disabled
[    1.172225] brcm-ahci f045a000.sata: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    1.181209] brcm-ahci f045a000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part
[    1.190756] scsi host0: brcm-ahci
[    1.194337] scsi host1: brcm-ahci
[    1.197820] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
[    1.205754] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
[    1.213690] brcm-ahci f045a000.sata: Broadcom AHCI SATA3 registered
[    1.220824] brcmstb_qspi f03e3400.spi: using bspi-mspi mode
[    1.226812] m25p80 spi32766.0: found mx25l6405d, expected m25p80
[    1.232848] m25p80 spi32766.0: mx25l6405d (8192 Kbytes)
[    1.238122] 6 ofpart partitions found on MTD device spi32766.0
[    1.243977] Creating 6 MTD partitions on "spi32766.0":
[    1.249134] 0x000000000000-0x000000200000 : "flash0.bolt"
[    1.255088] 0x000000200000-0x000000240000 : "flash0.macadr"
[    1.261139] 0x000000240000-0x000000280000 : "flash0.nvram"
[    1.267085] 0x000000280000-0x000000300000 : "flash0.devtree"
[    1.273206] 0x000000300000-0x000000800000 : "flash0.avail0"
[    1.279247] 0x000000000000-0x000000800000 : "flash0"
[    1.285315] libphy: Fixed MDIO Bus: probed
[    1.289875] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[    1.308212] libphy: bcmgenet MII bus: probed
[    1.333161] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.339012] e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
[    1.344992] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    1.352447] usbcore: registered new interface driver pegasus
[    1.358159] usbcore: registered new interface driver asix
[    1.363601] usbcore: registered new interface driver ax88179_178a
[    1.369735] usbcore: registered new interface driver cdc_ether
[    1.375633] usbcore: registered new interface driver cdc_ncm
[    1.381465] xhci-brcm: xHCI BRCM driver
[    1.385453] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.391246] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
[    1.399323] xhci-brcm f0471000.xhci_v2: hcc params 0x0250f17d hci version 0x100 quirks 0x00010090
[    1.408233] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
[    1.414866] hub 1-0:1.0: USB hub found
[    1.418645] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    1.425915] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
[    1.431675] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
[    1.439562] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.448010] hub 2-0:1.0: USB hub found
[    1.451785] hub 2-0:1.0: 2 ports detected
[    1.456163] ehci-brcm: EHCI BRCM driver
[    1.460109] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[    1.465885] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
[    1.483837] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
[    1.485219] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.485752] ata1.00: ATA-9: WDC WD10JPVX-75JC3T0, 02.01A02, max UDMA/133
[    1.485756] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    1.486301] ata1.00: configured for UDMA/133
[    1.486517] scsi 0:0:0:0: Direct-Access     ATA      WDC WD10JPVX-75J 1A02 PQ: 0 ANSI: 5
[    1.487135] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    1.487139] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.487274] sd 0:0:0:0: [sda] Write Protect is off
[    1.487328] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.487888] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.536310]  sda: sda1
[    1.536865] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.566218] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.572878] hub 3-0:1.0: USB hub found
[    1.576675] hub 3-0:1.0: 1 port detected
[    1.580903] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[    1.586689] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
[    1.595223] ata2: SATA link down (SStatus 0 SControl 300)
[    1.604661] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
[    1.616211] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[    1.622808] hub 4-0:1.0: USB hub found
[    1.626588] hub 4-0:1.0: 1 port detected
[    1.630839] ohci-brcm: OHCI BRCM driver
[    1.634792] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[    1.640573] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
[    1.648483] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
[    1.709620] hub 5-0:1.0: USB hub found
[    1.713402] hub 5-0:1.0: 1 port detected
[    1.717560] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[    1.723336] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
[    1.731284] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
[    1.792589] hub 6-0:1.0: USB hub found
[    1.796369] hub 6-0:1.0: 1 port detected
[    1.800575] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.807139] ehci-pci: EHCI PCI platform driver
[    1.811648] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.817854] ohci-pci: OHCI PCI platform driver
[    1.822454] usbcore: registered new interface driver usb-storage
[    1.828951] mousedev: PS/2 mouse device common for all mice
[    1.835075] i2c /dev entries driver
[    1.838740] gspca_main: v2.14.0 registered
[    1.843212] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
[    1.851245] brcmstb-cpufreq f03e257c.cpu-clk-div: registered
[    1.857228] sdhci: Secure Digital Host Controller Interface driver
[    1.863426] sdhci: Copyright(c) Pierre Ossman
[    1.867796] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.874638] sdhci-brcmstb f03e0000.sdhci: No vmmc regulator found
[    1.880750] sdhci-brcmstb f03e0000.sdhci: No vqmmc regulator found
[    1.888130] usb 3-1: new high-speed USB device number 2 using ehci-brcm
[    1.924216] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
[    1.933780] sdhci-brcmstb f03e0200.sdhci: No vmmc regulator found
[    1.939894] sdhci-brcmstb f03e0200.sdhci: No vqmmc regulator found
[    1.945218] usb 4-1: new high-speed USB device number 2 using ehci-brcm
[    1.983213] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[    1.990841] usbcore: registered new interface driver usbhid
[    1.996430] usbhid: USB HID core driver
[    2.002347] NET: Registered protocol family 17
[    2.006841] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.019653] Key type dns_resolver registered
[    2.023952] Registering SWP/SWPB emulation handler
[    2.029815] brcm-waketimer f0417580.waketimer: setting system clock to 1970-01-01 00:00:11 UTC (11)
[    2.043580] ALSA device list:
[    2.046579]   No soundcards found.
[    2.052717] Freeing unused kernel memory: 5140K (c0807000 - c0d0c000)
[    2.059229] mmc1: MAN_BKOPS_EN bit is not set
starting pid 12[    2.060924] usb-storage 3-1:1.0: USB Mass Storage device detected
58, tty '': '/etc/init.d/rcS'
M[    2.072780] scsi host2: usb-storage 3-1:1.0
ounting virtual filesystems
[    2.079513] hub 4-1:1.0: USB hub found
[    2.084547] hub 4-1:1.0: 4 ports detected
[    2.088870] mmc1: new high speed MMC card at address 0001
[    2.094647] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
[    2.099327] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
[    2.105443] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
[    2.111554] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
[    2.120866]  mmcblk0: p1 p2 p3 p4 p5
* WARNING: THIS STB CONTAINS GPLv3 SOFTWARE
* GPLv3 programs must be removed in order to enable security.
* See: http://www.gnu.org/licenses/gpl-faq.html#Tivoization
Configuring eth0 interface
[    2.206214] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
[    2.217410] bcmgenet f0b00000.ethernet: configuring instance for internal PHY
Configuring lo interface
Starting network services
starting pid 1317, tty '': '/bin/cttyhack /bin/sh -l'
# [    2.362218] usb 4-1.1: new high-speed USB device number 3 using ehci-brcm
[    2.456793] usb-storage 4-1.1:1.0: USB Mass Storage device detected
[    2.472696] scsi host3: usb-storage 4-1.1:1.0
[    3.081268] scsi 2:0:0:0: Direct-Access     Generic  USB  SD Reader   1.00 PQ: 0 ANSI: 0 CCS
[    3.090389] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.097024] sd 2:0:0:0: [sdb] 61831168 512-byte logical blocks: (31.7 GB/29.5 GiB)
[    3.106122] sd 2:0:0:0: [sdb] Write Protect is off
[    3.122305] sd 2:0:0:0: [sdb] No Caching mode page found
[    3.127682] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    3.146399]  sdb: sdb1
[    3.157993] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    3.225147] EXT4-fs (sdb1): couldn't mount as ext3 due to feature incompatibilities
[    3.234332] EXT4-fs (sdb1): couldn't mount as ext2 due to feature incompatibilities
[    3.350100] EXT4-fs (sdb1): recovery complete
[    3.354496] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[    3.643814] scsi 3:0:0:0: Direct-Access     JetFlash Transcend 4GB    1100 PQ: 0 ANSI: 4
[    3.652591] sd 3:0:0:0: Attached scsi generic sg2 type 0
[    3.658691] sd 3:0:0:0: [sdc] 7907328 512-byte logical blocks: (4.05 GB/3.77 GiB)
[    3.668465] sd 3:0:0:0: [sdc] Write Protect is off
[    3.683329] sd 3:0:0:0: [sdc] No Caching mode page found
[    3.688690] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[    3.716982]  sdc: sdc1
[    3.727064] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[    3.814292] random: sgdisk urandom read with 68 bits of entropy available
[    4.218319] bcmgenet f0b00000.ethernet eth0: Link is Down
[    4.843350]  mmcblk0:
[    5.925820]  mmcblk0: p1
[    6.079864] bcmgenet f0b00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    6.978517]  mmcblk0: p1 p2
[    8.041667]  mmcblk0: p1 p2 p3
[    9.142641]  mmcblk0: p1 p2 p3 p4
[   10.256224]  mmcblk0: p1 p2 p3 p4 p5
[   15.478169] random: nonblocking pool is initialized
[   16.843046] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to[   58.953329] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[   58.960261] reboot: Restarting system
CPU 01
BCM74390011
PRID07251111
v1.19
RR:00000200
BFW
seclib-1.9
BBL v1.0.1
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a252b25
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON

single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2525
MEMSYS-STD
SHMOO 02010000 BLD:11138 HW:hpf0_b1p6 V:2.1.0.0
MCB: FIX
AVS start:status=000000ff
STB: Current voltage=00000395(917)
temperature=00006c61(27745)
PV=00000351(849)
MV=00000393(915)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: *@ ffe0c7c8 <= ffe0c7c8 MEMSYS-0 @ f1100000 OK
DDR1: -
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss  0704e420
_ebss  0704fc88
_end   0704fca8
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0704e420 to 0704fc88 OK
CLR SRAM  OK
CACHE FLUSH OK
CPU CLKSET OK
GO!

    ,/
  ,'/___, BOLT v1.19 v1.19 LOCAL BUILD
.'__  ,'  (2016-10-14 22:06:19 doolgun@ubuntu)
   /,'    Copyright (C) 2016 Broadcom
  /'

Board: SF4008_EMMC_DDR4
SYS_CTRL: product=72511, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822080e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) memsys_1_disable(0x00008000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000461: moca2_disable(0x00000001) pcie1_disable(0x00000040) rfm_disable(0x00000020) sata1_disable(0x00000400)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1200MHz, DDR1 N/A
RESET CAUSE: 0x000200 software_master (1 of 23 possible causes)
CS0: SFDP SPI, 8MB, 64kB blocks, 64kB erase block, 256B pages
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 1
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.913V, T=+28.232C, PV=0.849V, MV=0.915V, FW=30333278 [0.3.2.x]
USB otp=00000040
Board version 0.92
HCS16SM18T Init
HCS16SM18T Reset
usb: resetting device on bus 0 hub 1 port 1
USB: New high speed device connected to bus 0 hub 1 port 1
usb: found Mass-Storage Device 090c:6200
USBMASS: Unit 0 connected
usb: resetting device on bus 1 hub 1 port 1
USB: New high speed device connected to bus 1 hub 1 port 1
usb: resetting device on bus 1 hub 2 port 1
USB: New high speed device connected to bus 1 hub 2 port 1
usb: found Mass-Storage Device 8564:1000
USBMASS: Unit 1 connected
Power Btn Init
LED Init
HDD Power Init
[ssbl/main/linux_dvb_7439.c::linux_dvb_usb_upgrade(653)] LINUX_DVB_DIR_PATH: sf4008
checking usbmass for upgrade
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** Generic  USB  SD Reader    (31659 MB, lbs=512) ***
*** Could not find a valid partition...status=00000000, ids=83000000!
Could not init file system: File system not recognized
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/update.bin: File found
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/force: File not found
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/noforce: File found
*** JetFlash Transcend 4GB     (4048 MB, lbs=512) ***
*** sf4008/rootfs.tar.bz2: File found
force:0 - noforce:1
[linux_dvb_upgrade:551] disk_number: 1
linux_dvb_wait_upgrade_button done
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:(null)
Reading 3388016 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7628000)

32 bit boot...
Booting Linux on physical CPU 0x0
Linux version 4.1.37 (eduard@kubuntu) (gcc version 6.2.0 (GCC) ) #2 SMP Tue Jan 30 02:24:58 EET 2018
CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c5387d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine model: SF4008_EMMC_DDR4
moving dtb from 0x0000000007628000 to 0x0000000000959804
bmem: Reserved 700 MiB at 0x0000000014400000
cma: Reserved 16 MiB at 0x0000000012c00000
Forcing write-allocate cache policy for SMP
Memory policy: Data cache writealloc
PERCPU: Embedded 12 pages/cpu @d23ae000 s16396 r8192 d24564 u49152
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 261512
Kernel command line: root=/dev/mmcblk0p4 rootwait rw vmalloc=692m bmem=700m@324m
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 296868K/1048576K available (6728K kernel code, 213K rwdata, 2100K rodata, 296K init, 190K bss, 735324K reserved, 16384K cma-reserved, 8188K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xd4000000 - 0xff000000   ( 688 MB)
    lowmem  : 0xc0000000 - 0xd3c00000   ( 316 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc08a7720   (8830 kB)
      .init : 0xc08a8000 - 0xc08f2000   ( 296 kB)
      .data : 0xc08f2000 - 0xc09275d0   ( 214 kB)
       .bss : 0xc092a000 - 0xc0959804   ( 191 kB)
Hierarchical RCU implementation.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
irq_brcmstb_l2: registered L2 intc (mem: 0xd4002000, parent irq: 93)
irq_brcmstb_l2: registered L2 intc (mem: 0xd4008000, parent irq: 64)
irq_brcmstb_l2: registered L2 intc (mem: 0xd400a640, parent irq: 95)
irq_brcmstb_l2: registered L2 intc (mem: 0xd400c200, parent irq: 58)
irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc40a700, parent IRQ(s): 2)
irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xd400e380, parent IRQ(s): 3)
MCP: Enabling write pairing
Architected cp15 timer(s) running at 27.00MHz (virt).
clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
Switching to timer-based delay loop, resolution 37ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: update cpu_capacity 1024
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x8440 - 0x8498
CPU1: update cpu_capacity 1024
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (108.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
Broadcom Brahma-B15 readahead cache at: 0xd410e478
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.20
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switched to clocksource arch_sys_counter
FS-Cache: Loaded
thermal thermal_zone0: failed to read out thermal zone (-22)
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
CPU PMU: Failed to parse /pmu/interrupt-affinity[0]
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
FS-Cache: Netfs 'cifs' registered for caching
Key type cifs.spnego registered
fuse init (API version 7.23)
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
brcm-gisb-arb f0400000.gisb-arb: registered mem: d4134000, irqs: 261, 262
brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
brcmstb-sata-phy f0458100.sata_phy: registered 2 port(s)
brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
brcm-pci f0460000.pcie: cannot get msi intr; MSI disabled
brcm-pci f0460000.pcie: link down
brcm-waketimer f0417580.waketimer: rtc core: registered brcmstb-waketmr as rtc0
brcm-waketimer f0417580.waketimer: registered, with irq 263
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
console [ttyS0] disabled
f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
console [ttyS0] enabled
of_serial: probe of f040a940.serial failed with error -28
of_serial: probe of f040a980.serial failed with error -28
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
brcm-ahci f045a000.sata: masking port_map 0x3 -> 0x3
brcm-ahci f045a000.sata: SSS flag set, parallel bus scan disabled
brcm-ahci f045a000.sata: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
brcm-ahci f045a000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part
scsi host0: brcm-ahci
scsi host1: brcm-ahci
ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
brcm-ahci f045a000.sata: Broadcom AHCI SATA3 registered
brcmstb_qspi f03e3400.spi: using bspi-mspi mode
m25p80 spi32766.0: found mx25l6405d, expected m25p80
m25p80 spi32766.0: mx25l6405d (8192 Kbytes)
6 ofpart partitions found on MTD device spi32766.0
Creating 6 MTD partitions on "spi32766.0":
0x000000000000-0x000000200000 : "flash0.bolt"
0x000000200000-0x000000240000 : "flash0.macadr"
0x000000240000-0x000000280000 : "flash0.nvram"
0x000000280000-0x000000300000 : "flash0.devtree"
0x000000300000-0x000000800000 : "flash0.avail0"
0x000000000000-0x000000800000 : "flash0"
libphy: Fixed MDIO Bus: probed
bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
bcmgenet f0b00000.ethernet: failed to get enet-mux clock
libphy: bcmgenet MII bus: probed
usbcore: registered new interface driver r8152
hso: /media/myhome/openpli-oe-core/build/tmp/work-shared/sf4008/kernel-source/drivers/net/usb/hso.c: Option Wireless
usbcore: registered new interface driver hso
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver ipheth
xhci-brcm: xHCI BRCM driver
xhci-brcm f0471000.xhci_v2: xHCI Host Controller
xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
xhci-brcm f0471000.xhci_v2: hcc params 0x0250f17d hci version 0x100 quirks 0x00010090
xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
xhci-brcm f0471000.xhci_v2: xHCI Host Controller
xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ehci-brcm: EHCI BRCM driver
ehci-brcm f0470300.ehci_v2: EHCI Host Controller
ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm f0470500.ehci_v2: EHCI Host Controller
ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
hub 4-0:1.0: USB hub found
ata1.00: ATA-9: WDC WD10JPVX-75JC3T0, 02.01A02, max UDMA/133
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD10JPVX-75J 1A02 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: Attached scsi generic sg0 type 0
hub 4-0:1.0: 1 port detected
ohci-brcm: OHCI BRCM driver
ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
ata2: SATA link down (SStatus 0 SControl 300)
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver appletouch
usbcore: registered new interface driver bcm5974
usbcore: registered new interface driver synaptics_usb
i2c /dev entries driver
brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
usb 3-1: new high-speed USB device number 2 using ehci-brcm
usbcore: registered new interface driver btusb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
sdhci-brcmstb f03e0000.sdhci: No vmmc regulator found
sdhci-brcmstb f03e0000.sdhci: No vqmmc regulator found
mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
sdhci-brcmstb f03e0200.sdhci: No vmmc regulator found
sdhci-brcmstb f03e0200.sdhci: No vqmmc regulator found
usb 4-1: new high-speed USB device number 2 using ehci-brcm
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
brcm-waketimer f0417580.waketimer: setting system clock to 1970-01-01 00:00:12 UTC (12)
ALSA device list:
  No soundcards found.
Waiting for root device /dev/mmcblk0p4...
usb-storage 3-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 3-1:1.0
mmc1: MAN_BKOPS_EN bit is not set
mmc1: new high speed MMC card at address 0001
mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
mmcblk0: p1 p2 p3 p4 p5
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 4 ports detected
EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:4.
devtmpfs: mounted
Freeing unused kernel memory: 296K (c08a8000 - c08f2000)
INIT: version 2.88 booting
usb 4-1.1: new high-speed USB device number 3 using ehci-brcm
usb-storage 4-1.1:1.0: USB Mass Storage device detected
scsi host3: usb-storage 4-1.1:1.0
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
Adding 524264k swap on /dev/mmcblk0p5.  Priority:-1 extents:1 across:524264k SSFS
EXT4-fs (mmcblk0p4): re-mounted. Opts: data=ordered
scsi 2:0:0:0: Direct-Access     Generic  USB  SD Reader   1.00 PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: [sdb] 61831168 512-byte logical blocks: (31.7 GB/29.5 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] No Caching mode page found
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
/dev/dvb/adapter0/video0: No such file or directory
EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
scsi 3:0:0:0: Direct-Access     JetFlash Transcend 4GB    1100 PQ: 0 ANSI: 4
sd 3:0:0:0: [sdc] 7907328 512-byte logical blocks: (4.05 GB/3.77 GiB)
sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: [sdc] No Caching mode page found
sd 3:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 3:0:0:0: [sdc] Attached SCSI removable disk
random: nonblocking pool is initialized
ALSA: Restoring mixer settings...
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_ratio = 60
INIT: Entering runlevel: 3
Configuring network interfaces... f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
bcmgenet f0b00000.ethernet: configuring instance for internal PHY
udhcpc: option -h NAME is deprecated, use -x hostname:NAME
udhcpc (v1.24.1) started
Sending discover...
bcmgenet f0b00000.ethernet eth0: Link is Down
Sending discover...
bcmgenet f0b00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Sending discover...
Sending select for 192.168.1.109...
Lease of 192.168.1.109 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 192.168.1.1
done.
Starting system message bus: dbus.
bootvideo found @ /usr/share/bootvideo.mp4
grep: /etc/enigma2/settings: No such file or directory
Setting pipeline to PAUSED ...
Pipeline is PREROLLING ...
WARNING: from element /GstPlayBin:playbin0/GstPlaySink:playsink: No volume control found
Additional debug info:
../../../git/gst/playback/gstplaysink.c(2883): gen_audio_chain (): /GstPlayBin:playbin0/GstPlaySink:playsink:
Volume/mute is not available
Pipeline is PREROLLED ...
Setting pipeline to PLAYING ...
New clock: GstSystemClock
ERROR: from element /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:vbin/GstDVBVideoSink:dvbvideosink0: There is no codec present that can handle the stream's type.
Additional debug info:
../git/gstdvbvideosink.c(1794): gst_dvbvideosink_set_caps (): /GstPlayBin:playbin0/GstPlaySink:playsink/GstBin:vbin/GstDVBVideoSink:dvbvideosink0:
hardware decoder can't handle streamtype 1
Execution ended after 0:00:00.004449815
Setting pipeline to PAUSED ...
Setting pipeline to READY ...
Setting pipeline to NULL ...
Freeing pipeline ...
Starting Dropbear SSH server: Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCwR1WGhM8kjZPlVBq5frQFV/4k54WQG5cIq6lw0tXvr9ynrOOoXIdI6QyHjAmGJaVacsVP4PKjxKpZE9WNQiugjSEXiLbZ4/dKpdN6vwc4a+Jk8ZFFtw7aV8S2d9iB4Vv93QuxXyTdGNZeWr94TIZm1wn/5KrYdkmqmoQ43tBoAQ== root@sf4008
Fingerprint: md5 40:1dNET: Registered protocol family 10
:30:67:b9:1b:9d:a0:43:e9:15:a7:3b:bf:66:1a
dropbear.
Starting rpcbind daemon...done.
Mounting remote filesystems...
starting statd: done
starting Busybox Periodic Command Scheduler: crond... done.
Starting internet superserver: inetdcrond[1451]: crond (busybox 1.24.1) started, log level 8

.
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
   ...done.
mount: mounting /dev/sda1 on /hdd failed: Device or resource busy
swap: missing /var/etc/settings.swap
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
INIT: Id "gui" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel

Ednaz

Пробуй 3 сборки. Если не пойдет, то хз... Нужно пробовать собирать с GCC 7
GI ET11000 4K, Duo4k, Ultimo4k, Solo4k, Uno4k, Uno4k SE, Zero4k, Octagon SF4008, AX HD51, Dreambox 900, Solo2, SoloSE v2, Zero, VU+Duo, Xtrend ET-9000, ET-9200, ET7000mini, Force1, Spark2, GI Fly и др.
Поблагодарить Z707779886070, E342760518570, R341155895525,  MasterCard 5168 7422 4047 5503monobank 5375 4141 1455 0253