Обсуждение VU+Zero4k

[Марчелла]

Light, так вроде всё необходимое зацепилось... и что стик так и не определился в настройках сети?

[Light]

и что стик так и не определился в настройках сети?

Перегрузил, вынул 2,4 свисток, оставил только 5ггц и опять только Лан 

Ни в какую не хочет, зараза

подкинь фид от ATV по пути etc/opkg что в прицепе, только свой сохрани...

Свой файл вернуть назад?

[sety]

Стало интересно) Взял такой свисток пробнуть, но как и обычно китайцы пишут что угодно, по факту оказался такой

Код Виділити Розширити

openpli develop vuduo4k
vuduo4k login: root
root@vuduo4k:~# lsusb
Bus 001 Device 003: ID 1a40:0101
Bus 001 Device 002: ID 1a40:0101
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0003
Bus 001 Device 006: ID 0bda:b82c
Bus 001 Device 007: ID 0a5c:0bdc
Bus 001 Device 004: ID 0a5c:2045
Тот что китайский определился как

Код Виділити Розширити

0bda:b82c
то есть 8822BU (там видно второй id это с duo4k встроенный wifi)
С фида закинул драйвера,

Код Виділити Розширити

openpli develop vuduo4k

vuduo4k login: root
root@vuduo4k:~# opkg install kernel-module-88x2bu
Installing kernel-module-88x2bu-4.1.45-1.17 (5.6.1) on root
Downloading http://downloads.openpli.org/feeds/openpli-develop/vuduo4k/kernel-module-88x2bu-4.1.45-1.17_5.6.1-r0.6_vuduo4k.ipk.
Configuring kernel-module-88x2bu-4.1.45-1.17.
root@vuduo4k:~#

свисток без проблем определился, думаю ты там что то делаеш не то совсем

[Light]

висток без проблем определился, думаю ты там что то делаеш не то совсем

Ввел команду

Код Виділити Розширити

opkg install kernel-module-88x2bu

Все равно только Lan. Что там может быть не так? 

[antonio6]

Возможно ли поймать сигнал на частоте 11817 v 31430 DVB-S2 16 APSK что на Астра 19,2 на этом ресивере.

[Serjoga]

Возможно ли поймать сигнал

Если тюнер DVB-S2X и в зоне покрытия то пробуйте

[falke]

Привет, такая проблема, при переключении на каналы BCU Сваты и ещё штук 10, звук идёт на всю мощь, и не реагирует на убывание, совсем убирается, а немного громче не делает, идёт зразу на всю громкость, есть ли решения проблемы. Спасибо

[Serjoga]

BCU Сваты и ещё штук 10,

Подозреваю что это айглюк за 1$, бежать от них надо. Нормальные сервера смотрят на VipSport 1 и 2 шахтёр с гого украинского а у них тишина...

[falke]

provider itv.live/ OpenPli 8,3. Брат смотрит на двух vuzero, и на простом vuzero всё нормально, а на vuzero4k такая проблема, загружал с плагином от Дорика и просто пакет для enigma2, и на обоих пакетах такая бяка, provider думаю не причём.

[sviridov55]

Кстати , у кого нибудь получилось на версиях выше 6.4 запустить отт-плай от алекса ?

Получилось на Open ATV 7.0 и прекрасно работает. А как быть с клоном китайским vu+zero4k. какой ATV на него установить или еще что другое? с  уважением sviridov55.

[sety]

с клоном китайским vu+zero4k

Впервые слышу, даже гугл об этом скромно молчит, откуда такая инфа?

[antonio6]

Дайте пожалуйста ссылку на  программу с помощью которой можно извлечь отдельные файлы из бэкапа

[falke]

Программа 7zip не подходит?

[Andrey3885]

Друзья, прошу помочь с восстановлением тюнера Vu+ Zero4K. После просмотра ТВ  обесточил тюнер, забыв перевести в "Глубокий режим ожидания". При следующем включении тюнер загрузился как обычно и всё работало без сбоев, но когда попытался выключить получил "зелёный экран" и перезапуск Enigma. Такая проблема наблюдается при Выключении(Глубокий режим ожидания)/Перезагрузке/Рестарте GUI. Пытался прошить имидж, тюнер плавно мигает секунд 20, после чего начинает мигать быстрее (прошивка завершена). Отключаю, вынимаю флешку, включаю, запускается старый имидж без изменений. Всё работает как и раньше но выключить или перезагрузить не могу. Тоже наблюдается при попытке дать команды init 4, init 6 через  Telnet. Enigma2_crash.log прилагаю

Spoiler

OpenPLi Enigma2 crash log

crashdate=Ср дек 20 17:33:11 2023
compiledate=Jul 30 2022
skin=PLi-FullNightHD/skin.xml
sourcedate=2022-07-24
branch=release-8.2
rev=1cafb70
component=Enigma2

stbmodel=zero4k
stbmodel=dm8000
kernelcmdline=root=/dev/mmcblk0p7 rootfstype=ext4 rootflags=data=journal rootwait rw coherent_pool=2M rw bmem=699m@1317m
nimsockets=NIM Socket 0:
imageissue=openpli 8.2-release %h


REMOVE Peer vuzero4k
REMOVE Peer vuzero4k


dmesg

<6>[    0.000000] Booting Linux on physical CPU 0x0
<5>[    0.000000] Linux version 4.1.20-1.9 (oe-user@oe-host) (gcc version 9.2.0 (GCC) ) #1 SMP Thu May 5 04:48:47 UTC 2022
<6>[    0.000000] CPU: ARMv7 Processor [420f1000] revision 0 (ARMv7), cr=30c5383d
<6>[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
<6>[    0.000000] Machine model: BCM972604USFF
<6>[    0.000000] moving dtb from 0x0000000007618000 to 0x00000000008d7850
<6>[    0.000000] bmem: Reserved 699 MiB at 0x0000000052500000
<6>[    0.000000] cma: Reserved 16 MiB at 0x0000000051400000
<4>[    0.000000] Forcing write-allocate cache policy for SMP
<6>[    0.000000] Memory policy: Data cache writealloc
<7>[    0.000000] On node 0 totalpages: 516096
<7>[    0.000000]   DMA zone: 512 pages used for memmap
<7>[    0.000000]   DMA zone: 0 pages reserved
<7>[    0.000000]   DMA zone: 65536 pages, LIFO batch:15
<7>[    0.000000]   HighMem zone: 450560 pages, LIFO batch:31
<6>[    0.000000] psci: probing for conduit method from DT.
<6>[    0.000000] psci: PSCIv0.2 detected in firmware.
<6>[    0.000000] psci: Using standard PSCI v0.2 function IDs
<6>[    0.000000] PERCPU: Embedded 12 pages/cpu @cefb9000 s16844 r8192 d24116 u49152
<7>[    0.000000] pcpu-alloc: s16844 r8192 d24116 u49152 alloc=12*4096
<7>[    0.000000] pcpu-alloc:

   
• 0
• 1

<6>[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515584
<5>[    0.000000] Kernel command line: root=/dev/mmcblk0p7 rootfstype=ext4 rootflags=data=journal rootwait rw coherent_pool=2M rw bmem=699m@1317m
<6>[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
<6>[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>[    0.000000] Memory: 1306468K/2064384K available (6140K kernel code, 311K rwdata, 2052K rodata, 308K init, 198K bss, 741532K reserved, 16384K cma-reserved, 1070076K highmem)
<5>[    0.000000] Virtual kernel memory layout:
<5>[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
<5>[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
<5>[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
<5>[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
<5>[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
<5>[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
<5>[    0.000000]       .text : 0xc0008000 - 0xc08084e4   (8194 kB)
<5>[    0.000000]       .init : 0xc0809000 - 0xc0856000   ( 308 kB)
<5>[    0.000000]       .data : 0xc0856000 - 0xc08a3e70   ( 312 kB)
<5>[    0.000000]        .bss : 0xc08a6000 - 0xc08d7850   ( 199 kB)
<6>[    0.000000] Hierarchical RCU implementation.
<6>[    0.000000]     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
<6>[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
<6>[    0.000000] NR_IRQS:16 nr_irqs:16 16
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0802000, parent irq: 89)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0808000, parent irq: 61)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd080aa00, parent irq: 62)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd080c640, parent irq: 91)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd080e200, parent irq: 57)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0810500, parent irq: 95)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0812400, parent irq: 96)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0814540, parent irq: 93)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0816440, parent irq: 94)
<6>[    0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xd0818480, parent irq: 98)
<6>[    0.000000] MCP: Enabling write pairing
<6>[    0.000000] Architected cp15 timer(s) running at 27.00MHz (phys).
<6>[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
<6>[    0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
<6>[    0.000010] Switching to timer-based delay loop, resolution 37ns
<6>[    0.000357] Console: colour dummy device 80x30
<6>[    0.000375] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
<6>[    0.000382] pid_max: default: 32768 minimum: 301
<6>[    0.000464] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[    0.000469] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[    0.000807] CPU: Testing write buffer coherency: ok
<6>[    0.001006] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
<6>[    0.001040] Setting up static identity map for 0x8480 - 0x84d8
<6>[    0.014751] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
<6>[    0.014791] Brought up 2 CPUs
<6>[    0.014801] SMP: Total of 2 processors activated (108.00 BogoMIPS).
<6>[    0.014805] CPU: All CPU(s) started in HYP mode.
<6>[    0.014807] CPU: Virtualization extensions available.
<6>[    0.015087] devtmpfs: initialized
<6>[    0.022766] VFP support v0.3: implementor 42 architecture 3 part 10 variant 0 rev 0
<6>[    0.022967] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
<6>[    0.023988] NET: Registered protocol family 16
<6>[    0.025124] DMA: preallocated 2048 KiB pool for atomic coherent allocations
<6>[    0.029897] cpuidle: using governor ladder
<6>[    0.035907] cpuidle: using governor menu
<6>[    0.041132] No ATAGs?
<6>[    0.041164] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
<6>[    0.041170] hw-breakpoint: maximum watchpoint size is 8 bytes.
<6>[    0.041442] Broadcom Brahma-B15 readahead cache at: 0xd0aaa478
<6>[    0.052093] brcmstb-gpio f040a400.gpio: Registered 3 banks (GPIO(s): 0-95)
<6>[    0.052263] brcmstb-gpio f04174c0.gpio: Registered 2 banks (GPIO(s): 96-159)
<5>[    0.052563] SCSI subsystem initialized
<7>[    0.052750] libata version 3.00 loaded.
<6>[    0.052905] usbcore: registered new interface driver usbfs
<6>[    0.052938] usbcore: registered new interface driver hub
<6>[    0.052964] usbcore: registered new device driver usb
<6>[    0.053013] Linux video capture interface: v2.00
<6>[    0.053063] pps_core: LinuxPPS API ver. 1 registered
<6>[    0.053066] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
<6>[    0.053093] PTP clock support registered
<6>[    0.053422] Advanced Linux Sound Architecture Driver Initialized.
<6>[    0.054353] Switched to clocksource arch_sys_counter
<5>[    0.054556] FS-Cache: Loaded
<4>[    0.060336] thermal thermal_zone0: failed to read out thermal zone (-22)
<6>[    0.060449] NET: Registered protocol family 2
<6>[    0.060785] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
<6>[    0.060803] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
<6>[    0.060824] TCP: Hash tables configured (established 2048 bind 2048)
<6>[    0.060862] UDP hash table entries: 256 (order: 1, 8192 bytes)
<6>[    0.060874] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
<6>[    0.060950] NET: Registered protocol family 1
<6>[    0.061162] RPC: Registered named UNIX socket transport module.
<6>[    0.061165] RPC: Registered udp transport module.
<6>[    0.061168] RPC: Registered tcp transport module.
<6>[    0.061171] RPC: Registered tcp NFSv4.1 backchannel transport module.
<7>[    0.061182] PCI: CLS 0 bytes, default 64
<4>[    0.061553] CPU PMU: Failed to parse /pmu/interrupt-affinity[0]
<6>[    0.061575] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
<6>[    0.062341] futex hash table entries: 512 (order: 3, 32768 bytes)
<5>[    0.063132] NFS: Registering the id_resolver key type
<5>[    0.063153] Key type id_resolver registered
<5>[    0.063156] Key type id_legacy registered
<6>[    0.063167] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
<6>[    0.063172] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
<6>[    0.063435] fuse init (API version 7.23)
<6>[    0.064066] bounce: pool size: 64 pages
<6>[    0.064095] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>[    0.064104] io scheduler noop registered
<6>[    0.064109] io scheduler deadline registered
<6>[    0.064128] io scheduler cfq registered (default)
<6>[    0.064389] brcm-gisb-arb f0400000.gisb-arb: registered mem: d0aca000, irqs: 261, 262
<6>[    0.064944] brcmstb-sata-phy f0b10100.sata_phy: registered 1 port(s)
<6>[    0.065284] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
<4>[    0.065335] brcm-pci f0460000.pcie: no identity map; PCI drivers may fail
<6>[    0.165479] brcm-pci f0460000.pcie: down
<6>[    0.166765] brcmstb_memc f1102000.memc-ddr: registered
<6>[    0.166950] brcm-waketimer f0417680.waketimer: registered, with irq 264
<6>[    0.167128] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
<6>[    0.168042] console [ttyS0] disabled
<6>[    0.168067] f040c000.serial: ttyS0 at MMIO 0xf040c000 (irq = 100, base_baud = 5062500) is a 16550A
<6>[    0.909815] console [ttyS0] enabled
<6>[    0.913658] f040d000.serial: ttyS1 at MMIO 0xf040d000 (irq = 101, base_baud = 5062500) is a 16550A
<6>[    0.922867] f040e000.serial: ttyS2 at MMIO 0xf040e000 (irq = 102, base_baud = 5062500) is a 16550A
<6>[    0.934877] loop: module loaded
<6>[    0.938716] brcm-ahci f0b12000.sata: controller can do ALPM, turning on CAP_ALPM
<4>[    0.946134] brcm-ahci f0b12000.sata: masking port_map 0x1 -> 0x1
<6>[    0.952167] brcm-ahci f0b12000.sata: SSS flag set, parallel bus scan disabled
<6>[    0.969367] brcm-ahci f0b12000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
<6>[    0.978345] brcm-ahci f0b12000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part
<6>[    0.986868] scsi host0: brcm-ahci
<6>[    0.990330] ata1: SATA max UDMA/133 mmio [mem 0xf0b12000-0xf0b1299b] port 0x100 irq 87
<6>[    0.998265] brcm-ahci f0b12000.sata: Broadcom AHCI SATA3 registered
<6>[    1.005653] libphy: Fixed MDIO Bus: probed
<6>[    1.010205] bcmgenet f0480000.ethernet: GENET 5.0 EPHY: 0x0000
<4>[    1.016085] bcmgenet f0480000.ethernet: failed to get enet-mux clock
<6>[    1.035351] libphy: bcmgenet MII bus: probed
<3>[    1.059500] Broadcom BCM7260 f0480000.etherne:01: failed to request GPHY clock
<6>[    1.067329] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
<6>[    1.073174] e1000e: Copyright(c) 1999 - 2014 Intel Corporation.
<6>[    1.079276] xhci-brcm: xHCI BRCM driver
<6>[    1.083270] ehci-brcm: EHCI BRCM driver
<6>[    1.101478] ehci-brcm f0b00300.ehci_v2: EHCI Host Controller
<6>[    1.103367] ata1: SATA down (SStatus 0 SControl 300)
<6>[    1.112658] ehci-brcm f0b00300.ehci_v2: new USB bus registered, assigned bus number 1
<6>[    1.130637] ehci-brcm f0b00300.ehci_v2: irq 120, io mem 0xf0b00300
<6>[    1.142358] ehci-brcm f0b00300.ehci_v2: USB 2.0 started, EHCI 1.00
<6>[    1.148932] hub 1-0:1.0: USB hub found
<6>[    1.152703] hub 1-0:1.0: 1 port detected
<6>[    1.156882] ehci-brcm f0b00500.ehci_v2: EHCI Host Controller
<6>[    1.162642] ehci-brcm f0b00500.ehci_v2: new USB bus registered, assigned bus number 2
<6>[    1.180588] ehci-brcm f0b00500.ehci_v2: irq 123, io mem 0xf0b00500
<6>[    1.192358] ehci-brcm f0b00500.ehci_v2: USB 2.0 started, EHCI 1.00
<6>[    1.198890] hub 2-0:1.0: USB hub found
<6>[    1.202663] hub 2-0:1.0: 1 port detected
<6>[    1.206890] ohci-brcm: OHCI BRCM driver
<6>[    1.210850] ohci-brcm f0b00400.ohci_v2: BRCM OHCI controller
<6>[    1.216603] ohci-brcm f0b00400.ohci_v2: new USB bus registered, assigned bus number 3
<6>[    1.224513] ohci-brcm f0b00400.ohci_v2: irq 121, io mem 0xf0b00400
<6>[    1.285707] hub 3-0:1.0: USB hub found
<6>[    1.289482] hub 3-0:1.0: 1 port detected
<6>[    1.293633] ohci-brcm f0b00600.ohci_v2: BRCM OHCI controller
<6>[    1.299393] ohci-brcm f0b00600.ohci_v2: new USB bus registered, assigned bus number 4
<6>[    1.307841] ohci-brcm f0b00600.ohci_v2: irq 124, io mem 0xf0b00600
<6>[    1.368712] hub 4-0:1.0: USB hub found
<6>[    1.372483] hub 4-0:1.0: 1 port detected
<6>[    1.376728] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[    1.383279] ehci-pci: EHCI PCI platform driver
<6>[    1.387792] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>[    1.393991] ohci-pci: OHCI PCI platform driver
<6>[    1.398564] usbcore: registered new interface driver usb-storage
<6>[    1.404726] mousedev: PS/2 mouse device common for all mice
<6>[    1.410762] i2c /dev entries driver
<6>[    1.414913] IR NEC protocol handler initialized
<6>[    1.419457] IR RC5(x/sz) protocol handler initialized
<6>[    1.424522] IR RC6 protocol handler initialized
<6>[    1.429064] IR JVC protocol handler initialized
<6>[    1.433605] IR Sony protocol handler initialized
<6>[    1.438233] IR SANYO protocol handler initialized
<6>[    1.442948] IR Sharp protocol handler initialized
<6>[    1.447663] IR MCE Keyboard/mouse protocol handler initialized
<6>[    1.453508] IR XMP protocol handler initialized
<6>[    1.458372] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
<6>[    1.466200] usb 1-1: new high-speed USB device number 2 using ehci-brcm
<6>[    1.510010] brcmstb-avs-cpufreq f04c4000.avs-cpu-data-mem: registered
<6>[    1.516700] sdhci: Secure Digital Host Controller Interface driver
<6>[    1.522892] sdhci: Copyright(c) Pierre Ossman
<6>[    1.527263] sdhci-pltfm: SDHCI platform and OF driver helper
<6>[    1.534426] sdhci-brcmstb f0200200.sdhci: No vmmc regulator found
<6>[    1.540532] sdhci-brcmstb f0200200.sdhci: No vqmmc regulator found
<6>[    1.577359] mmc0: SDHCI controller on f0200200.sdhci [f0200200.sdhci] using ADMA
<6>[    1.586981] usbcore: registered new interface driver usbhid
<6>[    1.592570] usbhid: USB HID core driver
<6>[    1.598900] NET: Registered protocol family 17
<5>[    1.603454] Key type dns_resolver registered
<5>[    1.607876] Registering SWP/SWPB emulation handler
<6>[    1.614939] ALSA device list:
<6>[    1.617925]   No soundcards found.
<6>[    1.623594] Waiting for root device /dev/mmcblk0p7...
<6>[    1.681023] mmc0: MAN_BKOPS_EN bit is not set
<6>[    1.691613] mmc0: new high speed MMC card at address 0001
<6>[    1.697217] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB
<6>[    1.701802] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB
<6>[    1.707773] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB
<6>[    1.713759] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB
<6>[    1.721944]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
<4>[    1.731815] EXT4-fs: Warning: mounting with data=journal disables delayed allocation and O_DIRECT support!
<4>[    1.752264] EXT4-fs warning (device mmcblk0p7): ext4_clear_journal_err:4735: Filesystem error recorded from previous mount: IO failure
<4>[    1.764370] EXT4-fs warning (device mmcblk0p7): ext4_clear_journal_err:4737: Marking fs in need of filesystem check.
<4>[    1.775355] EXT4-fs (mmcblk0p7): warning: mounting fs with errors, running e2fsck is recommended
<6>[    1.784503] EXT4-fs (mmcblk0p7): recovery complete
<6>[    1.789515] EXT4-fs (mmcblk0p7): mounted filesystem with journalled data mode. Opts: data=journal
<6>[    1.798427] VFS: Mounted root (ext4 filesystem) on device 179:7.
<6>[    1.805048] devtmpfs: mounted
<6>[    1.808223] Freeing unused kernel memory: 308K (c0809000 - c0856000)
<30>[    2.076543] udevd[734]: starting version 3.2.8
<5>[    2.088314] random: udevd urandom read with 7 bits of entropy available
<30>[    2.110938] udevd[735]: starting eudev-3.2.8
<6>[    2.337407] usb 1-1: reset high-speed USB device number 2 using ehci-brcm
<6>[    2.475614] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
<6>[    2.532628] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5370 detected
<7>[    2.546232] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[    2.546943] usbcore: registered new interface driver rt2800usb
<6>[    2.654826] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null)
<4>[    3.062968] procmk_init
<4>[    3.069332] bcm_event: module license 'Proprietary' taints kernel.
<4>[    3.075539] Disabling lock debugging due to kernel taint
<6>[    3.273840] nexus.ko: virtual irq: enabled (267)
<6>[    3.278560] nexus.ko: shared gpio banks: enabled
<6>[    6.347689] DVB: registering new adapter (_vuplus_zero4k_)
<4>[    6.820094] bcm7252s: hotplug_callback():
<4>[    6.820094] Hotplug - status.connected 1:0:1
<4>[    6.827191] bcm7252s: hotplug_callback():
<4>[    6.827191] Hotplug - connecting HDMI to display 0xe
<6>[    7.033356] brcm_demux_init: $Id: bcm_demux.c,v 0.7 $
<4>[    7.058393] [MPVR]: >> misc_pvr_init
<4>[    7.063043] [VID]:
6bcm7335_video_init
<4>[    7.067491] [AUD]:
6bcm7335_audio_init
<4>[    7.071450] [AUD]: >> bcm_audio_capture_init
<4>[    7.079362] qam=0, ofdm=0, satellite=1
<6>[    7.095780] BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (Vuplus FE)...
<6>[    7.137609] input: dreambox advanced remote control (native) as /devices/virtual/input/input0
<6>[    7.149474] [LCD]: registered
<6>[    7.257384] [CI]: registered ci0
<6>[    8.404923] [CI]: CI interface initialised
<6>[    8.404923]
<6>[    8.417423] [DFP]: registered dbox fp
<6>[    8.423616] [SC]: registered sci0
<4>[    8.569355] system_time_set wakeup mode get
<4>[    8.633364] system_time_set wakeup mode get 0xc4
<6>[    8.869243] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
<6>[    8.880945] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.36
<5>[   12.099801] random: nonblocking pool is initialized
<6>[   12.203600] NET: Registered protocol family 10
<6>[   12.209517] IPv6: ADDRCONF(NETDEV_UP): wlan0: is not ready
<6>[   12.422035] Bluetooth: Core ver 2.20
<6>[   12.428096] NET: Registered protocol family 31
<6>[   12.432564] Bluetooth: HCI device and connection manager initialized
<6>[   12.438954] Bluetooth: HCI socket layer initialized
<6>[   12.444193] Bluetooth: L2CAP socket layer initialized
<6>[   12.449285] Bluetooth: SCO socket layer initialized
<2>[   12.972833] EXT4-fs error (device mmcblk0p7): ext4_mb_generate_buddy:754: group 1, block bitmap and bg descriptor inconsistent: 27440 vs 27442 free clusters
<3>[   12.987161] Aborting journal on device mmcblk0p7-8.
<2>[   12.992433] EXT4-fs (mmcblk0p7): Remounting filesystem read-only
<2>[   12.998499] EXT4-fs error (device mmcblk0p7) in ext4_free_blocks:4873: Journal has aborted
<2>[   13.007328] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
<2>[   13.016751] EXT4-fs error (device mmcblk0p7) in ext4_ext_remove_space:3042: Journal has aborted
<2>[   13.026560] EXT4-fs error (device mmcblk0p7) in ext4_ext_truncate:4654: Journal has aborted
<2>[   13.035362] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
<2>[   13.044676] EXT4-fs error (device mmcblk0p7) in ext4_orphan_del:2987: Journal has aborted
<2>[   13.053198] EXT4-fs error (device mmcblk0p7) in ext4_reserve_inode_write:4980: Journal has aborted
<6>[   13.320682] wlan0: authenticate with c8:d7:19:5c:75:99
<4>[   13.344064] [VID]: VIDEO_SET_STREAMTYPE 1
<4>[   13.349582] [VID]: VIDEO_SELECT_SOURCE 1  0
<4>[   13.353846] [VID]: VIDEO_PLAY 1  5 0
<6>[   13.359998] wlan0: send auth to c8:d7:19:5c:75:99 (try 1/3)
<4>[   13.368896] [VID]: VIDEO_CONTINUE 1  1
<4>[   13.372898] [VID]: VIDEO_CLEAR_BUFFER 1  1 0
<6>[   13.393673] wlan0: authenticated
<6>[   13.398367] wlan0: associate with c8:d7:19:5c:75:99 (try 1/3)
<6>[   13.407645] wlan0: RX AssocResp from c8:d7:19:5c:75:99 (capab=0x411 status=0 aid=5)
<6>[   13.424374] wlan0: associated
<6>[   13.427464] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: becomes ready
<4>[   13.536399] [VID]: VIDEO_STOP 0  1
<4>[   13.540714] [VID]: VIDEO_SELECT_SOURCE 0  0
<4>[   16.625131] [AUD]: AUDIO_SET_MUTE 0
<4>[   16.629745] [AUD]: AUDIO_SET_MIXER -848085360
<4>[   16.634483] [AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
<4>[   16.639555] [AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
<4>[   16.646225] [AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
<4>[   20.146935] [AUD]: AUDIO_SET_MIXER -848085360
<4>[   20.151408] [AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
<4>[   20.156479] [AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
<4>[   20.163458] [AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
<4>[   21.010556] FE tune
<4>[   21.181134] [AUD]: AUDIO_SELECT_SOURCE 0
<4>[   21.186435] [AUD]: AUDIO_SET_BYPASS_MODE 9
<4>[   21.190635] [AUD]: AAC downmix 0  state : 0
<4>[   21.194839] [AUD]: AUDIO_PAUSE 9
<4>[   21.198163] [AUD]: AUDIO_PLAY 9 decoder start : 0
<4>[   21.205167] [VID]: VIDEO_SELECT_SOURCE 0  0
<4>[   21.209401] [VID]: VIDEO_GET_SIZE src w: 1920 h:1080 display w:1920 h:1080
<4>[   21.216310] [VID]: VIDEO_GET_SIZE aspect: 1 6
<4>[   21.220702] [VID]: VIDEO_SET_STREAMTYPE 1
<4>[   21.224875] [VID]: VIDEO_FREEZE -1095152524  0
<4>[   21.229330] [VID]: VIDEO_PLAY -1095152524  5 2
<4>[   21.239050] [VID]: VIDEO_SLOWMOTION 0    1
<4>[   21.243167] [VID]: VIDEO_FAST_FORWARD 0    1 0
<4>[   21.247628] [VID]: VIDEO_CONTINUE 0  1
<4>[   21.251478] [AUD]: AUDIO_CONTINUE 0 1 aph=0xceaf7f00
<4>[   21.256451] [AUD]: Mute : 0
<4>[   21.260067] [AUD]: AUDIO_CHANNEL_SELECT 0
<4>[   21.526634] [VID]: VIDEO_SLOWMOTION 0    1
<4>[   21.530839] [VID]: VIDEO_FAST_FORWARD 0    1 0
<4>[   21.535663] [VID]: VIDEO_CONTINUE 0  1
<4>[   21.539539] [AUD]: AUDIO_CONTINUE 0 1 aph=0xceaf7f00
<4>[   21.544542] [AUD]: Mute : 0
<4>[  119.433282] [VID]: VIDEO_STOP 1  1
<4>[  119.437016] [AUD]: AUDIO_STOP 5350880
<4>[  119.465505] [AUD]: AUDIO_CONTINUE 0 0 aph=0x0
<4>[  119.469878] [AUD]: AUDIO_CONTINUE aph=0 0 0
<4>[  119.794751] FE tune
<4>[  119.967854] [AUD]: AUDIO_SELECT_SOURCE 0
<4>[  119.973332] [AUD]: AUDIO_SET_BYPASS_MODE 0
<4>[  119.977569] [AUD]: AC3 downmix 0  state : 0
<4>[  119.981853] [AUD]: AUDIO_PAUSE 0
<4>[  119.985182] [AUD]: AUDIO_PLAY 0 decoder start : 0
<4>[  119.992587] [VID]: VIDEO_SELECT_SOURCE 0  0
<4>[  119.996825] [VID]: VIDEO_SET_STREAMTYPE 1
<4>[  120.001020] [VID]: VIDEO_FREEZE -1095152524  0
<4>[  120.005477] [VID]: VIDEO_PLAY -1095152524  5 2
<4>[  120.017461] [VID]: VIDEO_SLOWMOTION 0    1
<4>[  120.022885] [VID]: VIDEO_FAST_FORWARD 0    1 0
<4>[  120.030090] [VID]: VIDEO_CONTINUE 0  1
<4>[  120.036703] [AUD]: AUDIO_CONTINUE 0 1 aph=0xce9b9f80
<4>[  120.043232] [AUD]: Mute : 0
<4>[  120.050568] [VID]: VIDEO_GET_SIZE src w: 0 h:0 display w:0 h:0
<4>[  120.056428] [VID]: VIDEO_GET_SIZE aspect: 1 0
<4>[  129.136859] [VID]: VIDEO_STOP 1  1
<4>[  129.140311] [AUD]: AUDIO_STOP 5350304
<4>[  129.168838] [AUD]: AUDIO_CONTINUE 0 0 aph=0x0
<4>[  129.173218] [AUD]: AUDIO_CONTINUE aph=0 0 0
<4>[  129.474785] FE tune
<4>[  129.643047] [AUD]: AUDIO_SELECT_SOURCE 0
<4>[  129.648557] [AUD]: AUDIO_SET_BYPASS_MODE 9
<4>[  129.652761] [AUD]: AAC downmix 0  state : 0
<4>[  129.657068] [AUD]: AUDIO_PAUSE 9
<4>[  129.660400] [AUD]: AUDIO_PLAY 9 decoder start : 0
<4>[  129.666371] [VID]: VIDEO_SELECT_SOURCE 0  0
<4>[  129.670596] [VID]: VIDEO_SET_STREAMTYPE 1
<4>[  129.674787] [VID]: VIDEO_FREEZE -1095152524  0
<4>[  129.679288] [VID]: VIDEO_PLAY -1095152524  5 2
<4>[  129.689002] [VID]: VIDEO_SLOWMOTION 0    1
<4>[  129.693134] [VID]: VIDEO_FAST_FORWARD 0    1 0
<4>[  129.697687] [VID]: VIDEO_CONTINUE 0  1
<4>[  129.701572] [AUD]: AUDIO_CONTINUE 0 1 aph=0xceaf9880
<4>[  129.706548] [AUD]: Mute : 0
<4>[  129.713596] [VID]: VIDEO_GET_SIZE src w: 0 h:0 display w:0 h:0
<4>[  129.719460] [VID]: VIDEO_GET_SIZE aspect: 1 0
<4>[  130.208800] [VID]: VIDEO_SLOWMOTION 0    1
<4>[  130.212979] [VID]: VIDEO_FAST_FORWARD 0    1 0
<4>[  130.217919] [VID]: VIDEO_CONTINUE 0  1
<4>[  130.221829] [AUD]: AUDIO_CONTINUE 0 1 aph=0xceaf9880
<4>[  130.226820] [AUD]: Mute : 0
<4>[  236.928416] [VID]: VIDEO_STOP 1  1
<4>[  236.931877] [AUD]: AUDIO_STOP 4736776
<4>[  236.960215] [AUD]: AUDIO_CONTINUE 0 0 aph=0x0
<4>[  236.964596] [AUD]: AUDIO_CONTINUE aph=0 0 0

[Serjoga]

перезапуск Enigma

Попробуйте перешить голым OpenATV, у меня было похожое только простой зеро был не 4к. Прошивал и все не как, только после голово OpenATV смог потом опять нормально прошиватся.